View source for Nooelec SDR: Setup

== Summary == 

We want to get started with the NooElec SDR. Specifically the NESDR Nano 2+ and the NESDR SMArt. At the end of the setup, the SDR will be ready to use and we will be able to see the first incoming radio signals.
The Steps taken to install any NESDR Device should be the same according to Nooelec. This Setup shows mostly the installation and usage under Linux, these devices can also be used under Windows however the software options are limited.

== Requirements ==

* Operating System: Ubuntu 20.04 is used in this Tutorial, but it also works with other Linux distributions


== Description ==

=== Installation ===

Run the command:
 lsusb
If you have your NESDR device plugged into your Ubuntu computer. This will list all of the USB devices attached to the computer. If things are working as they should be, you will see the NESDR SMArt listed as: 
 RealtekSemiconductor Corp. RTL2838 DVB-T.
The DVB-T is the important part, because it means that the operating system has recognized the device and loaded, what it believes to be, the correct driver.

[[File:Nooelec picture 1.png]]

Can also be seen when using command: 
 lsmod | grep dvb
This lists the loaded modules (drivers) and filters them to just show the ones that have the letters dvb in them. You will see they are loaded.

[[File:Nooelec picture 2.png]]

We need to remove those modules (drivers) and load the appropriate ones using the device as an SDR. We start by “blacklisting” the default drivers. This is done by editing the file:
 /etc/modprobe.d/blacklist-dvb.conf
Add the following line to blacklist this file:
 blacklist dvb_usb_rtl28xxu

[[File:Nooelec picture 3.png]]

Then reboot and check. You should get nothing when running lsmod | grep dvb again.

[[File:Nooelec picture 4.png]]

What that does is disallow the default module (driver) to load. Now we need to tell it to load the driver we want. First, we need to download it onto the computer with:
 sudo apt-get install rtl-sdr
This will have the drivers and utilities related to using a SDR.
Now test the SDR if it works at the lowest level, which is tuning on a particular frequency and seeing if we hear anything. We do this by executing:
 rtl_test

[[File:Nooelec picture 5.png]]

The first part of the test will test the parameters of the SDR and then it will attempt to tune in to a frequency. It is at this point you want the test to stop printing to the screen. You have the modules and libraries loaded that are needed to run the dongle as a software defined radio. The next step is to use a software, like Gqrx, that has a “waterfall display”, as you will see. With Ubuntu, the easiest way to do that is with Gqrx. It is available in the Ubuntu Software store, and therefore, easy to install.

[[File:Nooelec picture 6.png]]

However you will also need GNU radio to run Gqrx. Therefore it is recommended to simply install it via CLI with:
 sudo apt-get install gnuradio gqrx

=== Receiving Radio Signal ===

Having the device connected to the PC and the appropriate antenna, open a terminal and launch gqrx with the command:
 gqrx

[[File:Nooelec picture 7.png]]

Make sure that the Device line shows the FunCube Dongle or the device you are using. Leave the other fields as they are then click OK. The main window of gqrx looks as below, you can listen to radio if you switch mode to WFM (stereo) – for example go to 104.2 MHz for Radio Energy in Vienna.

[[File:Nooelec picture 8.png]]

== Used Hardware ==

* [[NooElec SDR Kit]]
* [[NESDR Nano 2+: Tiny RTL-SDR USB Set w/ 0.5PPM TCXO, R820T2 Tuner & Antenna]]

== Courses ==

* Wahlfachprojekt 1 (2021)

== Used Hardware ==

[[NooElec SDR Kit]]

== References ==

* https://medium.com/poka-techblog/a-newbies-guide-to-software-defined-radios-on-kali-linux-part-1-fun-with-fm-radios-3a3589b78608
* https://www.nooelec.com/store/qs
* https://www.nooelec.com/store/downloads/dl/file/id/72/product/0/nesdr_installation_manual_for_ubuntu.pdf

[[Category:Documentation]]