ChameleonMini RevE Rebooted - Revision history

LSchertler at 13:26, 14 December 2024

2024-12-14T13:26:36Z

← Older revision		Revision as of 13:26, 14 December 2024
Line 81:		Line 81:
	===GUI Usage with Chameleon Mini GUI v1.3.0.5 in Windows===		===GUI Usage with Chameleon Mini GUI v1.3.0.5 in Windows===
	=== Step 1 ===		=== Step 1 ===
	First you need to install the software in order to have a GUI to use the Chameleon Mini. The Version 1.3.0.5 can be downloaded here (http://www.icesql.se/download/ChameleonMiniGUI/publish.htm)		First you need to install the software in order to have a GUI to use the Chameleon Mini. The Version 1.3.0.6 can be downloaded here (http://www.icesql.se/download/ChameleonMiniGUI/publish.htm)
	Afterwards connect the Chameleon Mini RevE Rebooted with an USB-Cable to your PC. The first LED with the label "TAG1" now lights up red.		Afterwards connect the Chameleon Mini RevE Rebooted with an USB-Cable to your PC. The first LED with the label "TAG1" now lights up red.

NKirnbauer: merging similar articles

2024-11-10T19:59:40Z

merging similar articles

Show changes

FChallakhi: Added the chapter ChameleonMini in Use

2021-02-24T20:35:04Z

Added the chapter ChameleonMini in Use

← Older revision		Revision as of 20:35, 24 February 2021
Line 23:		Line 23:

	[[File:ChameleonMiniSuccess.PNG\|500px]]		[[File:ChameleonMiniSuccess.PNG\|500px]]

			== ChameleonMini in Use ==

			In the first tab "Operation" of the Chameleon Mini GUI, up to eight different memory slots can be freely configured. In order to change an entry, the corresponding box of the entry must first be marked. Then one of four different variants can be selected in the "Mode" selection and any ID can be entered in the UID input field as shown below in the screenshot.

			[[File:ChameleonOperation.PNG\|500px]]

			Below this, you can configure what happens when the button is pressed briefly or for a long time.
			[[File:ChameleonButton.PNG\|300px]]

			To save the changes made, the "Apply" button must be clicked at the bottom. It is possible to edit several entries at the same time. To do this, simply select the corresponding checkboxes.

			To emulate an RFID tag, first press the red button on the ChameleonMini RevE Rebooted. Now the memory slot that was marked as active in the software is active. Accordingly, the red LED lights up. Alternatively, ChameleonMini RevE Rebooted is activated when an RFID reader is detected. Then it activates automatically and the corresponding LED lights up. Depending on how the buttons have been configured, it is possible to switch through to RFID emulation through the corresponding memory loads.


	== References ==		== References ==

FChallakhi: changed the size of the pictures

2021-02-24T20:29:41Z

changed the size of the pictures

← Older revision		Revision as of 20:29, 24 February 2021
Line 3:		Line 3:
	The RFID Multitool ChameleonMini is a powerful and portable RFID emulation and manipulation tool that can emulate RFID tags, read tokens and sniff the radio communication. The credit card-shaped housing and integrated battery make it suitable for mobile use. In addition, transmissions can be read out and all data can be conveniently processed on the computer. Using a freely available open-source application, the ChameleonMini can be conveniently configured via a graphical user interface. Otherwise, it can be connected to a smartphone via USB cable or, in part, via Bluetooth and can thus also be configured on the move. This makes it possible, for example, to read an access card in passing and emulate it directly with the ChameleonMini and thus open a (actually protected) door. The ChameleonMini hardware is capable of emulating various ISO 14443, NFC and ISO 15693 cards, as well as other types of RFID transponders operating at 13.56 MHz. The ChameleonMini hardware consists of a PCB antenna driven by power transistors on the board to generate a 13.56 MHz RFID field. They thus function as an active RFID reader. An integrated Li-Ion battery can be charged via USB and enables stand-alone operation. The core of the hardware is an Atmel ATXMega128A4U microcontroller. The AES and DES hardware engines in the microcontroller enable very fast calculation of the cryptographic algorithms.		The RFID Multitool ChameleonMini is a powerful and portable RFID emulation and manipulation tool that can emulate RFID tags, read tokens and sniff the radio communication. The credit card-shaped housing and integrated battery make it suitable for mobile use. In addition, transmissions can be read out and all data can be conveniently processed on the computer. Using a freely available open-source application, the ChameleonMini can be conveniently configured via a graphical user interface. Otherwise, it can be connected to a smartphone via USB cable or, in part, via Bluetooth and can thus also be configured on the move. This makes it possible, for example, to read an access card in passing and emulate it directly with the ChameleonMini and thus open a (actually protected) door. The ChameleonMini hardware is capable of emulating various ISO 14443, NFC and ISO 15693 cards, as well as other types of RFID transponders operating at 13.56 MHz. The ChameleonMini hardware consists of a PCB antenna driven by power transistors on the board to generate a 13.56 MHz RFID field. They thus function as an active RFID reader. An integrated Li-Ion battery can be charged via USB and enables stand-alone operation. The core of the hardware is an Atmel ATXMega128A4U microcontroller. The AES and DES hardware engines in the microcontroller enable very fast calculation of the cryptographic algorithms.

	[[File:Chameleon-Mini-RevE-Rebooted.jpg]]		[[File:Chameleon-Mini-RevE-Rebooted.jpg\|500px]]

	== Requirements ==		== Requirements ==
Line 22:		Line 22:
	The first LED with the label "TAG1" now lights up red. Now switch to the "Settings" tab, a photo is displayed there and there is a green message with the designation "CONNECTED! In the lower area with the messages, "Success, found Chameleon Mini device on 'COMX' with Firmware RevE rebooted installed" appears like in the screenshot below. The ChameleonMini RevE Rebooted is now ready for use.		The first LED with the label "TAG1" now lights up red. Now switch to the "Settings" tab, a photo is displayed there and there is a green message with the designation "CONNECTED! In the lower area with the messages, "Success, found Chameleon Mini device on 'COMX' with Firmware RevE rebooted installed" appears like in the screenshot below. The ChameleonMini RevE Rebooted is now ready for use.

	[[File:ChameleonMiniSuccess.PNG]]		[[File:ChameleonMiniSuccess.PNG\|500px]]

	== References ==		== References ==

FChallakhi: Created page with "== Introduction == The RFID Multitool ChameleonMini is a powerful and portable RFID emulation and manipulation tool that can emulate RFID tags, read tokens and sniff the rad..."

2021-02-24T20:27:07Z

Created page with "== Introduction == The RFID Multitool ChameleonMini is a powerful and portable RFID emulation and manipulation tool that can emulate RFID tags, read tokens and sniff the rad..."

New page

== Introduction ==

The RFID Multitool ChameleonMini is a powerful and portable RFID emulation and manipulation tool that can emulate RFID tags, read tokens and sniff the radio communication. The credit card-shaped housing and integrated battery make it suitable for mobile use. In addition, transmissions can be read out and all data can be conveniently processed on the computer. Using a freely available open-source application, the ChameleonMini can be conveniently configured via a graphical user interface. Otherwise, it can be connected to a smartphone via USB cable or, in part, via Bluetooth and can thus also be configured on the move. This makes it possible, for example, to read an access card in passing and emulate it directly with the ChameleonMini and thus open a (actually protected) door. The ChameleonMini hardware is capable of emulating various ISO 14443, NFC and ISO 15693 cards, as well as other types of RFID transponders operating at 13.56 MHz. The ChameleonMini hardware consists of a PCB antenna driven by power transistors on the board to generate a 13.56 MHz RFID field. They thus function as an active RFID reader. An integrated Li-Ion battery can be charged via USB and enables stand-alone operation. The core of the hardware is an Atmel ATXMega128A4U microcontroller. The AES and DES hardware engines in the microcontroller enable very fast calculation of the cryptographic algorithms.

[[File:Chameleon-Mini-RevE-Rebooted.jpg]]

== Requirements ==

* ChameleonMini
* PC having Windows (it is also possible to use a Android Phone, but this setup will be will on a Windows-PC.

== Setup ==

=== Step 1 ===

First you need to install the software in order to have a GUI to use the Chameleon Mini. The Version 1.3.0.5 can be downloaded here (http://www.icesql.se/download/ChameleonMiniGUI/publish.htm)
Afterwards connect the ChameleonMini RevE Rebooted with an USB-Cable to your PC.

=== Step 2 ===

The first LED with the label "TAG1" now lights up red. Now switch to the "Settings" tab, a photo is displayed there and there is a green message with the designation "CONNECTED! In the lower area with the messages, "Success, found Chameleon Mini device on 'COMX' with Firmware RevE rebooted installed" appears like in the screenshot below. The ChameleonMini RevE Rebooted is now ready for use.

[[File:ChameleonMiniSuccess.PNG]]

== References ==

* https://github.com/iceman1001/ChameleonMini-rebootedGUI
* https://scheible.it/chameleon-mini/

[[Category:Documentation]]